The Brocade ADX offers 3 types of HA. There are :<\/p>\n
Sym Active-Standby<\/strong> – Sym Active-Standby is only available on Router code. Both devices receive traffic but only the VIP with the highest sym-priority processes the traffic. Below is the configuration for Sym Active-Standby. <\/p>\n It is important to note that when configuring the VRID the command ‘backup priority 105 track-priority 10’ defines :<\/p>\n server symmetric-port ethernet 15 vlan-id 2<\/td>\n server symmetric-port ethernet 15 vlan-id 2<\/td>\n<\/tr>\n int ve 20 int ve 20 Next each Virtual Server is assigned a sym-priority. The system with a Virtual Server with the highest Sym Priority processes the traffic. Each Virtual Server IP is assigned to a VIP Group and finally each port profile is configured to synchronize sessions between nodes.<\/p>\n The configuration methods for Sym Active-Active are the same as Sym Active-Standby, apart from the command ‘sym-active’ which is applied to each Virtual Server.<\/p>\n Below shows the configuration steps for configuring Active-Standby.<\/p>\n <\/p>\n
Sym Active-Active<\/strong> – Sym Active-Active is only available on Router code. Both devices receive traffic, traffic for each VIP can processed by either ADX.
Switch Mode<\/strong> – Switch Mode is only available on Switch code. One ADX is always active whilst the other ADX is standby. <\/p>\nSym Active-Standby<\/strong><\/h3>\n
\n
\n\n
\n MASTER<\/span><\/strong><\/td>\n SECONDARY<\/span><\/strong><\/td>\n<\/tr>\n \n trunk ethernet 15 to 16
trunk deploy<\/td>\ntrunk ethernet 15 to 16
trunk deploy<\/td>\n<\/tr>\n\n vlan 2 name SYNC-LINK by port
untagged e 15
no spanning-tree
int e 15
speed 1000-full
enable<\/p>\nvlan 2 name SYNC-LINK by port
untagged e 15
no spanning-tree
int e 15
speed 1000-full
enable<\/p>\n\n conf t
router vrrp-extended
int ve 10
ip vrrp-extended vrid 10
backup priority 105 track-priority 20
advertise backup
ip-address 192.168.100.1
vip-group 1
track-port e 1
track-port e 5
enable<\/p>\n
ip vrrp-extended vrid 20
backup priority 105 track-priority 20
advertise backup
ip-address 192.168.200.1
track-port e 1
track-port e 5
enable<\/td>\nconf t
router vrrp-extended
int ve 10
ip vrrp-extended vrid 10
backup priority 100 track-priority 20
advertise backup
ip-address 192.168.100.1
vip-group 1
track-port e 1
track-port e 5
enable<\/p>\n
ip vrrp-extended vrid 20
backup priority 100 track-priority 20
advertise backup
ip-address 192.168.200.1
track-port e 1
track-port e 5
enable<\/td>\n<\/tr>\n\n config-sync sender ethernet 15 mac 001b.eb20.9a19 vlan-id 2<\/td>\n config-sync receiver ethernet 15 vlan-id 2<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n \n\n
\n server virtual VIP1 192.168.100.25
sym-priority 19<\/td>\nserver virtual VIP1 192.168.100.25
sym-priority 10<\/td>\n<\/tr>\n\n server vip-group 1
vip 192.168.100.25<\/td>\nserver vip-group 1
vip 192.168.100.25<\/td>\n<\/tr>\n\n server port 80
session-sync
tcp<\/td>\nserver port 80
session-sync
tcp<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\nSym Active-Active<\/strong><\/h3>\n
Active-Standby<\/strong><\/h3>\n
\n\n
\n MASTER<\/strong><\/span><\/td>\n SECONDARY<\/strong><\/span><\/td>\n<\/tr>\n \n trunk ethernet 15 to 16
trunk deploy<\/td>\ntrunk ethernet 15 to 16
trunk deploy<\/td>\n<\/tr>\n\n vlan 2 name SYNC-LINK by port
untagged e 15
no spanning-tree
int e 15
speed 1000-full
enable<\/td>\nvlan 2 name SYNC-LINK by port
untagged e 15
no spanning-tree
int e 15
speed 1000-full
enable<\/td>\n<\/tr>\n\n config-sync sender ethernet 15 mac 001b.eb20.9a19 vlan-id 2<\/td>\n config-sync receiver ethernet 15 vlan-id 2<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n \n\n
\n <\/td>\n <\/td>\n<\/tr>\n \n <\/td>\n <\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"excerpt":{"rendered":"